A medium-sized Clover Fountain with a brass center nozzle creating a high center stream and angled spray patterns in a pond, surrounded by trees.
clover 1 2 hp
clover
Authorized Dealer
Scott Aerator

Scott Aerator

Scott Aerator Clover Fountain For Medium, Residential Ponds

$2,599.00 $2,739.00
-5%
In stock
Motor: ¾ hp 115 volts
  • ¾ hp 115 volts
  • ¾ hp 230 volts
  • 1 hp 115 volts
  • 1 hp 230 volts
  • 1½ hp 230 volts
Cord Length: 100 feet
  • 100 feet
  • 150 feet - Unavailable
  • 200 feet - Unavailable
  • 250 feet - Unavailable

Estimated delivery between October 25 and October 27.

Free Shipping
Residential and Commercial Use
Backed by Real Expert Support
Delivered With Care, Direct to Your Door
Scott Aerator Clover Fountain For Medium, Residential Ponds
$2,599.00 $2,739.00
$2,599.00 $2,739.00
Options
Motor: ¾ hp 115 volts
  • ¾ hp 115 volts
  • ¾ hp 230 volts
  • 1 hp 115 volts
  • 1 hp 230 volts
  • 1½ hp 230 volts
Cord Length: 100 feet
  • 100 feet
  • 150 feet - Unavailable
  • 200 feet - Unavailable
  • 250 feet - Unavailable

Quick Facts

Feature Detail
Motor Options 3/4 HP, 1 HP, or 1-1/2 HP
Voltage 115V or 230V, depending on motor configuration
Flow Rate 65, 75, or 90 gallons per minute
Maximum Spray Up to 40 feet high by 45 feet wide
Motor Oil-Free Stainless Steel Submersible Motor
Operation Designed for 24-Hour-Per-Day Operation
Water Compatibility Fresh Water and Salt Water
Motor Warranty 5 Years
Made In Holland, Michigan, USA

A Note Before You Order

Select the correct motor voltage and power configuration before purchasing. A GFCI is required, and Scott Aerator recommends using a licensed electrical contractor. Do not use an extension cord to supply power to the motor. For 115V installations, the distance from the main breaker to the fountain should not exceed the applicable cable limit. If swimmers are present, always disconnect power to the fountain.

Scott Aerator Clover Fountain for Medium, Residential Ponds

The Clover Fountain creates a distinctive water display with one prominent center stream surrounded by four angled streams. The pattern spreads across the pond while adding movement, sound, and water circulation to the area around the fountain.

The medium residential Clover Fountain is available with 3/4 HP, 1 HP, and 1-1/2 HP motor configurations. Depending on the selected motor, the fountain can produce a spray from 25 to 40 feet high and 30 to 45 feet wide.

The oil-free stainless steel submersible motor is designed for continuous operation and can be used in both fresh and salt water. Optional LED light sets can be added at the time of purchase or later, allowing the fountain display to continue after sunset.

Configuration Guide

Clover Fountain 3/4 HP

Available in 115V or 230V with a 65 GPM flow rate. The 3/4 HP configuration requires a minimum pond depth of 40 inches and produces a spray approximately 25 feet high by 30 feet wide.

The 115V version uses a 100-foot, 10-gauge submersible power cord with plug. The 230V version uses a 100-foot, 12-gauge submersible power cord. Longer cords are available.

Clover Fountain 1 HP

Available in 115V or 230V with a 75 GPM flow rate. The 1 HP configuration requires a minimum pond depth of 44 inches and produces a spray approximately 30 feet high by 38 feet wide.

The 115V version uses a 100-foot, 10-gauge submersible power cord with plug. The 230V version uses a 100-foot, 12-gauge submersible power cord. Longer cords are available.

Clover Fountain 1-1/2 HP

The 1-1/2 HP configuration operates at 230V and provides a 90 GPM flow rate. It requires a minimum pond depth of 50 inches and produces a spray approximately 40 feet high by 45 feet wide.

The 1-1/2 HP model includes a 100-foot, 12-gauge submersible power cord, with longer cord lengths available.

Specifications & Details
Specification Detail
Motor Options 3/4 HP, 1 HP, and 1-1/2 HP
Voltage 115V or 230V; 1-1/2 HP is 230V
Frequency 60 Hz
Phase Single Phase
Motor Speed 3,450 RPM
Flow Rate 65, 75, or 90 GPM
Minimum Pond Depth 40 inches for 3/4 HP; 44 inches for 1 HP; 50 inches for 1-1/2 HP
Spray Dimensions 25' H x 30' W for 3/4 HP; 30' H x 38' W for 1 HP; 40' H x 45' W for 1-1/2 HP
Power Cord 100 feet standard; longer cords available
Water Compatibility Fresh Water or Salt Water
Operation 24 Hours Per Day
Maintenance No Routine Maintenance Required
Motor Warranty 5 Years
Installation & Assembly

Included Components

The assembly includes the float platform, pump assembly, stainless steel filter, stainless steel bolts, nuts, washers, and screws needed for assembly.

Assembly

The float is secured to the fountain housing with the supplied stainless steel hardware. The stainless steel filter is installed beneath the fountain using the supplied screws, followed by installation of the fountain head once the unit is positioned in the water.

Anchoring

Two nylon anchoring ropes attach to the fountain's stainless steel eye bolts. The ropes can be secured to shore or connected to two concrete blocks submerged at least 20 feet apart. Anchoring ropes and weights are not included.

Electrical Installation

A GFCI is required. Scott Aerator recommends using a licensed electrical contractor for the electrical connection, and the supplied instructions specifically state that an extension cord must not be used to supply power to the motor.

Maintenance & Winter Operation

Routine Maintenance

The fountain is designed to require little to no routine maintenance. When the unit is removed from the water, the manufacturer recommends washing it with high-pressure water and visually checking the fountain for debris or anything that could restrict water flow.

Winter Operation

The manufacturer recommends leaving the fountain in the water during winter. Turn the power supply off while the water is frozen and restore power after the water thaws. The instructions state that the fountain components can withstand sub-zero conditions without damage.

Anchoring Rope Replacement

Quality nylon anchoring rope that is 3/8 inch or thicker should be replaced approximately every five years. This is also a suitable time to inspect and clean the fountain.

Safety & Electrical Requirements

GFCI Protection

A Ground Fault Circuit Interrupter is required for operation. The manufacturer also recommends that electrical installation be completed by a licensed electrical contractor.

Power Cable

Do not use an extension cord to supply power to the motor. Cable size and maximum distance from the motor to the main power source must be selected according to the motor configuration and installation requirements.

Swimmer Safety

Always disconnect power to the fountain when swimmers are present.

Accessories & Options
Option What It Does
LED Light Sets Optional two-light or four-light LED sets can be added to illuminate the fountain after dark.
Night Glo LED Lights Optional fountain lighting for nighttime display.
Color-Changing LED Lights Optional programmable color-changing LED lighting for the fountain display.
Extended Power Cord Longer power cord lengths are available when required by the installation.
Warranty

5-Year Motor Warranty

The Clover Fountain includes an unconditional 5-year motor warranty according to Scott Aerator's product information. Warranty coverage remains subject to the manufacturer's applicable terms and conditions.

Frequently Asked Questions
Question Answer
What is the Clover Fountain designed to do? It creates a decorative fountain display while circulating water and supporting oxygen transfer throughout the pond.
What motor sizes are available for the medium residential Clover? The medium residential model is available with 3/4 HP, 1 HP, and 1-1/2 HP motor configurations.
What voltage options are available? The 3/4 HP and 1 HP models are available in 115V or 230V. The 1-1/2 HP model is available in 230V.
How large is the fountain spray? The 3/4 HP model sprays approximately 25 feet high by 30 feet wide, the 1 HP model approximately 30 feet high by 38 feet wide, and the 1-1/2 HP model approximately 40 feet high by 45 feet wide.
What pond depth is required? The 3/4 HP model requires at least 40 inches of water depth, the 1 HP model requires 44 inches, and the 1-1/2 HP model requires 50 inches.
Can the Clover Fountain be used in salt water? Yes. Scott Aerator states that the Clover Fountain is designed for use in both fresh water and salt water.
Can the fountain run continuously? Yes. The Clover Fountain is designed for 24-hour-per-day operation.
Does the fountain require winterizing? The manufacturer recommends leaving the fountain in the water during winter, turning off the power while the water is frozen, and restoring power after the water thaws.
Is a GFCI required? Yes. A GFCI is required for the fountain installation.
Can I use an extension cord? No. The manufacturer specifically states that an extension cord should not be used to supply power to the motor.
How is the Clover Fountain anchored? Two nylon ropes attach to the fountain's eye bolts. The fountain can be secured to shore or anchored with two concrete blocks submerged at least 20 feet apart.
Are lights included? No. LED light sets are optional and can be added when purchasing the fountain or later.
Downloads

Pond Fountain Motor Specs

View Pond Fountain Motor Specs PDF

Pond Fountain Specs & Assembly

View Pond Fountain Specs & Assembly PDF

Pond Fountain Comparison Brochure

View Pond Fountain Comparison Brochure PDF

Product Video

Watch the Clover Fountain video for a visual look at the fountain's spray pattern and operation.